Luminex 100 IS Developer Workbench Guide Version 2.3 Manual de usuario Pagina 27
- Pagina / 74
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
xMAP Technology Create Template
PN 89-00002-00-084 Rev. B 21
Qualitative Assay
Template
You define each Qualitative template using a single product. The
product must contain one standard. The standard is assigned a
Drain to reservoir Removes and refills sheath fluid from the cuvette.
Sheath fluid is expelled into the reservoir.
Drain to well Removes and refills sheath fluid from the cuvette.
Sheath fluid is expelled into a well.
Prime Primes the system to remove air from the sheath
side of the analyzer.
Sanitize Acquires sanitizing solution from the reservoir to
sanitize or eliminate air in the cuvette.
Skip Program a well skip into template.
Soak from
Reservoir
Soaking the probe replaces sheath fluid in the
probe with distilled water. You should perform the
Soak command at the end of each day. Place at
least 2 mL of distilled water in the reservoir.
Soak from Well Soaking the probe replaces sheath fluid in the
probe with distilled water. You should perform the
Soak command at the end of each day. Place at
least 275 µL of distilled water in the well.
Verify CON 1 Acquire CON 1 beads from a well to verify that the
system is working within the calibrated settings.
Verify CON 2 Acquire CON 2 beads from a well to verify that the
system is working within the calibrated settings.
Warmup Checks for proper system warm up and if needed
begins the warmup process.
Wash from
Reservoir
Acquires wash solution from reservoir to wash the
system. Place at least 2 mL of solution in the
reservoir.
Wash from Well Acquires wash solution from a well to wash the
system. Place at least 200 µL in the well.
XY Heater Off Turns the heater off.
XY Heater On Sets the indicated temperature (XyHtrTemp), turns
the heater on, and continues to the next command.
XY Heater On
(wait)
Sets the indicated temperature (XyHtrTemp), turns
the heater on, waits for the heater to stabilize at
the heater set point (with a 30 minute timeout), and
then continues to the next command.
Table 3: Available Commands (Continued)
Command Definition
- Luminex 100 1
- IS Developer 1
- Workbench Guide Version 2.3 1
- PN 89-00002-00-084 Rev. B 2
- August, 2005 2
- Contents 3
- A xMAP Protocols 49 4
- Version 1.7 61 5
- C Customize Splash Screen 63 5
- Index 65 5
- Technology 6
- Developer Workbench Guide 7
- General Guidelines 8
- Instructions 9
- Instrument Calibrators 12
- Developer 13
- Workbench 13
- Software 13
- Procedures 14
- Dialog Box Buttons 15
- Create New Product 15
- 10 PN 89-00002-00-084 Rev. B 16
- PN 89-00002-00-084 Rev. B 11 17
- 12 PN 89-00002-00-084 Rev. B 18
- PN 89-00002-00-084 Rev. B 13 19
- 14 PN 89-00002-00-084 Rev. B 20
- Quantitative Assay 21
- Template 21
- 16 PN 89-00002-00-084 Rev. B 22
- PN 89-00002-00-084 Rev. B 17 23
- Note: You can use the same 23
- 18 PN 89-00002-00-084 Rev. B 24
- Figure 7. Select Bead IDs 24
- PN 89-00002-00-084 Rev. B 19 25
- Qualitative Assay 27
- 22 PN 89-00002-00-084 Rev. B 28
- PN 89-00002-00-084 Rev. B 23 29
- 24 PN 89-00002-00-084 Rev. B 30
- PN 89-00002-00-084 Rev. B 25 31
- Figure 13. Select Bead IDs 31
- 26 PN 89-00002-00-084 Rev. B 32
- PN 89-00002-00-084 Rev. B 27 33
- PN 89-00002-00-084 Rev. B 29 35
- 30 PN 89-00002-00-084 Rev. B 36
- PN 89-00002-00-084 Rev. B 31 37
- 32 PN 89-00002-00-084 Rev. B 38
- Figure 21. Select Bead IDs 38
- PN 89-00002-00-084 Rev. B 33 39
- 34 PN 89-00002-00-084 Rev. B 40
- Maintenance 41
- Edit an Unused 42
- Edit a Used 43
- To edit a used template: 43
- Delete an Unused 44
- Delete a Used 45
- To delete a used template: 45
- Print Template 46
- Information 46
- PN 89-00002-00-084 Rev. B 41 47
- Technology 48
- To import a template: 49
- To export a template: 50
- About Developer 51
- Luminex Technical 53
- Support Website 53
- Handling 55
- Enumeration of xMAP 56
- Microsphere Suspensions 56
- PN 89-00002-00-084 Rev. B 51 57
- Protein Coupling Protocol 58
- Procedure 59
- Coupling 60
- Blocking, and 60
- PN 89-00002-00-084 Rev. B 55 61
- Equipment •Vortex 62
- PN 89-00002-00-084 Rev. B 57 63
- Enumerate the Coupled 64
- Microspheres 64
- LumAvidin Binding Protocol 65
- 60 PN 89-00002-00-084 Rev. B 66
- Version 1.7 67
- 62 PN 89-00002-00-084 Rev. B 68
- Customize Splash Screen 69
- 64 PN 89-00002-00-084 Rev. B 70
- PN 89-00002-00-084 Rev. B 65 71
- 66 PN 89-00002-00-084 Rev. B 72
- PN 89-00002-00-084 Rev. B 67 73
Relacionado con productos y manuales para Equipo Luminex 100 IS Developer Workbench Guide Version 2.3
Equipo Luminex 100 IS Version 2.1 Manual de usuario
(202 paginas)
(202 paginas)
Equipo Luminex 100 IS Version 2.3 Manual de usuario
(230 paginas)
(230 paginas)
Equipo Luminex 100 IS Version 2.1 Manual de usuario
(192 paginas)
(192 paginas)
Equipo Luminex IS Version 2.3 Manual de usuario
(7 paginas)
(7 paginas)
Equipo Luminex IS Version 2.3 Manual de usuario
(144 paginas)
(144 paginas)
Equipo Luminex IS Version 2.3 (IVD) Manual de usuario
(116 paginas)
(116 paginas)
Equipo Luminex IS Version 2.3 Manual de usuario
(120 paginas)
(120 paginas)
Equipo Luminex IS Version 2.3 Manual de usuario
(140 paginas)
(140 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales