Luminex xPONENT 4.0 SP1 Manual de usuario Pagina 103
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
91
Touring the Software
Batch Options Tab
Use this tab to set options for acquisition and batch analysis.
FIGURE 58. Batch Options Tab
This tab contains the following:
Batch Options. This section displays the following options:
• Allow running a batch if the instrument is not warmed up - Allows batches to run if
the instrument is not warmed up.
• Allow running a calibration if the instrument is not warmed up - Allows calibration
to run if the instrument is not warmed up.
• Allow running a batch with expired reagents - Allows batches to run with expired
reagents.
• Allow running a batch if XY temperature is not in range - Allows batches to run if
the XY temperature is not in range.
• Allow running a batch if the instrument is not calibrated or verified - Allows
batches to run if the instrument is not calibrated.
• Use Weighting as default option for quantitative analysis - Sets the weighting for
quantitative analysis to default to ON for new protocols.
• Warn when saving/running a New Batch with New Protocol without saving the
Protocol and/or Standard and Control information - Enables a dialog box warning
when saving or running a new batch with a new protocol when you haven’t saved the
protocol and/or standard and control information.
• Prompt for reacquiring of the last errored wells for an aborted partial batch -
Allows users to choose to reacquire aborted wells when resuming a stopped/partial
batch or to start with the next unacquired well.
Batch Settings. This section displays the following options:
- xPONENT 1
- 4.0 SP1™ 1
- Software Manual 1
- Software 5
- Table of Contents 9
- Contents 11
- Introduction 13
- About This Guide 14
- Warnings, Notes and Symbols 14
- General Guidelines 15
- Bead Concentration 16
- Sample Volume 17
- Sample Dilution 17
- Reagents 18
- Touring the Software 19
- Help Icons 20
- Screen Elements 21
- System Monitor 22
- Home Page 24
- Samples Tab 26
- Create Sample Tab 27
- Batches Tab 28
- Batch Plate Layout Report 29
- Protocol Tab 30
- Stds & Ctrls Tab 31
- Plate Layout Tab 33
- Save Protocol Dialog Box 35
- Settings Tab 36
- Logistic 5P. Type the 38
- Analytes Tab 39
- Analysis Settings Dialog Box 40
- Create a New MultiBatch 45
- • Print. Prints report 47
- • Save. Saves report 47
- Multibatch Report dialog box 48
- Current Batch Tab 49
- Saved Batches Tab 55
- Filter Setup Dialog Box 56
- Select Replay Mode Dialog Box 58
- Results Tab 60
- • Message 62
- Sample Details Tab 63
- Reports Tab 64
- LIS Results Tab 64
- Analytes Tab 71
- Std/Ctrl Details Tab 79
- Maintenance 80
- Auto Maint Tab 81
- Lot Management Tab 82
- Cmds & Routines Tab 83
- Probe and Heater Tab 87
- System Info Tab 89
- System Status Tab 91
- Support Utility Tab 92
- System Setup Tab 94
- LIS Settings 95
- • #p - Protocol name 96
- • #b - Batch name 96
- • #u - Logged in user name 96
- Group Setup Tab 97
- User Setup Tab 100
- Create User Account Screen 101
- Batch Options Tab 103
- Alert Options Tab 105
- Setup Email Dialog Box 106
- CSV Options Tab 107
- Cancel - Cancels changes 108
- Save - Saves changes 108
- Archive Tab 109
- Licensing Tab 110
- Schedule Tab 111
- Report Options Tab 112
- Using the Software 113
- System Setup 114
- Data Conversion 115
- Group Setup 116
- User Setup 116
- Batch Options 117
- Alert Options 117
- CSV Options 118
- Licensing 119
- Schedule 119
- Report Options 119
- Adjusting the Sample Probe 120
- System Initialization 120
- Run System Initialization 121
- Add CAL or VER Kits 121
- Managing Sample Lists 122
- Setting Up Batches 123
- Create a Multi-Batch 126
- Import Batch 126
- Export Batch 126
- Performing Analysis 127
- Analyze Current Batch 128
- Manage Saved Batches 128
- Analyze Saved Batch 129
- View Batch Settings 130
- View Batch Logs 130
- View Sample Details 130
- View and Print Reports 131
- Transmit a Batch 131
- Protocols 131
- Import Protocol 136
- Add New Lot for Protocol 136
- Delete Protocol 136
- Export Protocol 136
- Lots and Kits 137
- Performing System Maintenance 138
- Perform System Calibration 139
- Manage Maintenance Routines 139
- Support Utility 140
- Shutting Down the Analyzer 141
- Logging Out of the Software 141
- Exiting the Software 141
- Technical Support 141
- Luminex Website 141
- Glossary 143
Relacionado con productos y manuales para Software Luminex xPONENT 4.0 SP1
Software Luminex xPONENT 3.1 Manual de usuario
(192 paginas)
(192 paginas)
Software Luminex xPONENT 4.01 SP1 Manual de usuario
(172 paginas)
(172 paginas)
Software Luminex xPONENT 4.0 SP1 Manual de usuario
(188 paginas)
(188 paginas)
Software Luminex xPONENT 3.1 Manual de usuario
(184 paginas)
(184 paginas)
Software Luminex xPONENT 3.1 Rev 2 Manual de usuario
(145 paginas)
(145 paginas)
Software Luminex xPONENT for MAGPIX Manual de usuario
(145 paginas)
(145 paginas)
Software Luminex xPONENT 4.1 Manual de usuario
(173 paginas)
(173 paginas)
Software Luminex xPONENT for MAGPIX Manual de usuario
(140 paginas)
(140 paginas)
Software Luminex xPONENT for MAGPIX Manual de usuario
(144 paginas)
(144 paginas)
Software Luminex xPONENT for MAGPIX Manual de usuario
(149 paginas)
(149 paginas)
Software Luminex xPONENT for MAGPIX Manual de usuario
(126 paginas)
(126 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales